Beyond Part 97: the other FCC rules hams live under
Part 97 is our rulebook, but our radios share the air, the power lines and the neighborhood with plenty of other electronics. Four other parts of the FCC’s rules decide who has to fix a problem, who has to put up with one, and what gear may be sold.
The short version
Part 97 tells you how to operate a ham station. The rules below cover everything around you: the phone charger, the neighbor’s LED lights, a microwave oven, the cable line outside. The ARRL points to these four parts as the ones most likely to matter when interference comes up. In plain terms:
- Most everyday electronics may not cause harmful interference to a licensed station like yours, and the owner has to stop if the FCC says so.
- Those same devices are allowed to emit small amounts of RF, and the legal limits are not always low enough to protect a weak-signal ham receiver.
- A few places, such as the microwave-oven bands, are shared, and there you may be the one who has to put up with noise.
Part 2: Frequency allocations and general rulesWhere the ham bands come from and how radio equipment gets approved
Part 2 is the foundation under every other part. You will rarely read it cover to cover, but several of its sections come up for hams.
The Table of Frequency Allocations (§2.106)
Under §2.102, assigning and using any frequency from 8.3 kHz to 275 GHz has to follow this table. It is where the amateur bands, and whether a band is shared with other services, are set. Part 97 then says what hams may do inside those bands.
Definitions that apply everywhere (§2.1)
- Amateur service: a radiocommunication service for self-training, intercommunication and technical investigations, carried out by authorized people interested in radio technique solely with a personal aim and without pecuniary interest.
- Harmful interference: interference that endangers a radionavigation or other safety service, or seriously degrades, obstructs or repeatedly interrupts a radiocommunication service operating under the rules. Because Part 2 says its definitions prevail throughout the FCC’s rules, this same wording shows up in Parts 15, 18 and 76.
Equipment rules
- External power amplifiers (§2.815). Selling, leasing, advertising or importing an outboard amplifier that can operate below 144 MHz requires FCC certification. It must not amplify 26–28 MHz (the CB range) and must not be easy to modify to do so. No more than 10 may be built for evaluation before applying. An amplifier meant for the Amateur Radio Service must also meet §§97.315 and 97.317, which are covered on our Part 97 page.
- Amateur equipment testing (§2.1060). When ham gear is certified, spurious-emission tests have to be made on at least one frequency in each band the radio can tune.
- Marketing (§2.803). Selling or advertising RF devices before they are authorized is restricted. “Marketing” includes listing regulated gear on an online marketplace alongside services like warehousing, order processing or fulfillment.
- Testing before authorization (§2.805). A device can be operated before authorization only in limited cases, such as under an experimental license or inside a shielded room or anechoic chamber.
RF exposure (§§2.1091 and 2.1093)
These sections set how manufacturers evaluate RF exposure for mobile devices (kept at least 20 cm from the body) and portable devices. They are written for equipment makers. Hams have their own station-evaluation rules in Part 97.
Part 15: Radio frequency devicesThe rules for gadgets that may emit RF without a license
Part 15 covers electronics that create RF energy and may be used without an individual license. Whether the device transmits on purpose or just leaks a little, Part 15 governs it.
| Kind of device | What it does | Examples |
|---|---|---|
| Intentional radiator | Deliberately sends out RF (basically a transmitter) | Cordless phones, baby monitors, garage door openers, Wi-Fi |
| Unintentional radiator | Makes RF for internal use but is not meant to radiate it | Computers, routers, digital circuits, receivers |
| Incidental radiator | Makes RF as a side effect, not by design | DC motors, mechanical switches, power lines |
The rule that matters most: §15.5
- You have no vested right to keep using a frequency just because your device was certified.
- Operation is allowed only if it causes no harmful interference, and the device must accept interference from authorized stations (that includes hams), other Part 15 devices, ISM equipment and incidental radiators.
- If the FCC says a device is causing harmful interference, the operator must stop using it until the cause is corrected.
“Legal” does not mean “quiet”
The emission limits were written to keep one household’s gadgets from bothering the next house’s TV. They were not written for a sensitive ham receiver. The ARRL’s example: the general limit of 30 µV/m at 30 meters on 80 meters would read about S9 plus 15 dB on a dipole. That is a legal signal and still harmful interference.
| Limit (at 3 m) | 30–88 MHz | 88–216 MHz | 216–960 MHz | Above 960 MHz |
|---|---|---|---|---|
| Home digital devices, Class B (§15.109) | 100 µV/m | 150 µV/m | 200 µV/m | 500 µV/m |
| Transmitters under the general rule (§15.209) | 100 µV/m | 150 µV/m | 200 µV/m | 500 µV/m |
Below 30 MHz, transmitters under §15.209 are limited to 30 µV/m measured at 30 m between 1.705 and 30 MHz. Power-line conducted limits for Class B devices (§15.107) now start at 150 kHz and are written in dBµV. The older ARRL article quotes a 250 µV limit from 450 kHz, so use the current eCFR numbers.
Class A and Class B
Class A digital devices are marketed for commercial or industrial settings. Class B are marketed for homes and must meet stricter limits. Look for the label or manual statement: “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” (§15.19)
The manual for a Class B device also has to suggest fixes (§15.105): reorient or relocate the receiving antenna, increase the separation, plug into a different circuit, or ask a dealer or experienced radio/TV technician for help. You can point a neighbor to their own owner’s manual.
More Part 15 sections hams run into
- Power line carrier systems (§15.113). Utilities may run signals on their lines between 9 and 490 kHz on a non-interference basis. A utility may not start a new or modified system in 135.7–137.8 kHz or 472–479 kHz if a previously coordinated amateur station (§97.301(g)(2)) is within 1 km of the lines.
- Exempt devices (§15.103). Digital devices used only in vehicles, appliances such as microwave ovens and dishwashers, or industrial and medical test gear skip the technical limits. They still must obey §15.5 and stop if they cause harmful interference.
- Home-built gear (§15.23). Authorization is not required if the device is not marketed, not built from a kit, built in quantities of five or fewer and kept for personal use. You are still expected to use good engineering practice, and §15.5 applies.
- Designers should expect hams (§15.17). Manufacturers are told to consider nearby high-power stations, amateur stations included, when picking frequencies.
- Periodic transmitters (§15.231). Remote controls, alarm sensors and similar devices above 70 MHz may send short bursts at higher field strengths. Today’s rule lets them send data along with a control signal.
Sharing the ham bands
Many unlicensed devices operate on frequencies that overlap ham allocations, on a secondary, no-interference basis. Common examples are the 902–928 MHz band (LoRa mesh radios such as Meshtastic are typically sold for this under §15.247), 2.4 GHz and 5.8 GHz Wi-Fi, and several microwave segments. The ARRL’s list also shows overlap near 3.3–3.6 GHz, 10.5 GHz, 24 GHz and 76 GHz.
Part 18: Industrial, scientific and medical equipmentMicrowave ovens, RF lighting, diathermy and other devices that use RF without communicating
ISM equipment creates RF to do work, such as heating, ionizing gases, vibrating transducers or hair removal, rather than to carry messages. Familiar examples are home microwave ovens, jewelry cleaners, ultrasonic humidifiers and RF lighting.
ISM bands and your ham bands
ISM equipment can legally radiate unlimited energy inside its assigned band (§18.305(a)). Several of those bands sit on top of amateur allocations:
| ISM frequency (§18.301) | Tolerance | Overlaps ham band |
|---|---|---|
| 915 MHz | ± 13 MHz | 902–928 MHz |
| 2450 MHz | ± 50 MHz | 2300–2310 and 2390–2450 MHz |
| 5800 MHz | ± 75 MHz | 5.650–5.925 GHz |
| 24.125 GHz | ± 125 MHz | 24.0–24.25 GHz |
| 245 GHz | ± 1 GHz | 241–250 GHz |
Other ISM frequencies (6.78, 13.56, 27.12 and 40.68 MHz, plus 61.25 and 122.5 GHz) are also listed in §18.301.
You may have to accept it
The normal duty to fix interference does not apply when the victim is a station operating in an ISM band, or when a receiver picks up the fundamental of ISM equipment that is operating in its band and otherwise complies (§18.115(c) and (d)). If a compliant microwave oven bothers your 2.4 GHz link, the rules put the burden on you.
Everywhere else, the operator must fix it
- ISM equipment needs enough shielding and filtering to suppress emissions outside its bands (§18.109).
- If it causes harmful interference, the operator must promptly correct it (§18.111). If the FCC Regional Director says it endangers a radionavigation or safety service, the operator must stop immediately and may resume only to fix the problem.
- The Regional Director can require an engineer to investigate, and Part 18 sets deadlines for interim and final reports of 30 and 60 days (§18.117).
- Emissions outside ISM bands have field-strength limits. Between 30 and 1000 MHz, consumer equipment is held to 10, 15 and 20 µV/m at 30 m, and non-consumer equipment to 30, 50 and 70 µV/m (§18.305(b)).
Off limits for everyone
ISM equipment may not operate in these safety, search and rescue bands (§18.303): 490–510 kHz, 2170–2194 kHz, 8354–8374 kHz, 121.4–121.6 MHz, 156.7–156.9 MHz and 242.8–243.2 MHz.
RF lighting
Makers of RF lighting devices (certain LED and fluorescent bulbs) must include an advisory that the product may interfere with radio equipment and should not be installed near maritime safety or other critical communication equipment between 0.45 and 30 MHz (§18.213(d)). RF lighting has its own field-strength and conducted limits (§§18.305(c) and 18.307(c)). This is why a bargain LED bulb can ruin an HF band.
Part 76: Multichannel video and cable televisionWhen the cable on your street leaks signal, or when it picks up yours
Cable systems carry many signals inside a shielded cable. If a connector is loose or a cable is damaged, those signals can leak out and cause interference. Part 76 sets the leakage rules.
- Aeronautical band protection (§§76.610–76.612). Systems that carry signals in 108–137 MHz and 225–400 MHz must meet leakage criteria, test at least once each calendar year and keep their carriers offset from aviation frequencies.
- Regular monitoring (§76.614). Operators must check the plant for leaks about every three months, with equipment able to detect 20 µV/m at 3 meters, and repair leaks within a reasonable time.
- Emergency frequencies (§76.616). Cable carriers are prohibited near 121.5, 156.8 and 243.0 MHz, and limited in power from 405.925 to 406.176 MHz.
- Harmful interference (§76.613). A cable operator that causes harmful interference to any radiocommunication service must promptly eliminate it. For safety-of-life interference that cannot be fixed, the FCC can order the operation suspended.
- Who is responsible (§76.617). Trouble from the customer’s own terminal equipment is the customer’s responsibility under Part 15. The cable operator is still responsible for finding and fixing leakage, and its remedy is to cut off service to that subscriber until the leak is repaired.
Who has to give way?
| Interference source | Must it stop harming a ham station? | Must a ham accept it? |
|---|---|---|
| Part 15 device (computer, charger, Wi-Fi, gadget) | Yes (§15.5) | No, but the device must accept interference from your station |
| Incidental radiator (motor, power line) | Yes, use good engineering (§15.5, §15.13) | No |
| ISM equipment outside its ISM band | Yes (§18.111, §18.115) | No |
| ISM equipment inside its ISM band (e.g., 2.45 GHz oven) | No for stations in that band | Yes (§18.115) |
| Cable system leakage | Yes (§76.613) | No |
I hear noise on my radio. Now what?
- Check your own house first. Run a battery-powered radio and switch off breakers one at a time to see whether the noise is yours.
- Find the direction and character. A portable AM radio or handheld with a directional antenna is the classic noise hunter.
- Talk to the owner kindly. They bought a legal product. Point them to their manual’s interference section (§15.105 or §18.213) and offer to help.
- Contact the right party. That could be the manufacturer, the electric utility or the cable company (cite §76.613).
- Ask for help. Use the ARRL’s RFI resources below. If the problem continues, the FCC can order a device shut down.
Read the rules and get help
- Part 2, Part 15, Part 18 and Part 76 on the eCFR
- ARRL: FCC Rules and Regulations (the source of this page’s overview)
- ARRL RFI home page, power line noise and the Technical Information Service
- FCC Part 15 enforcement letters
Rule text is from the eCFR (authoritative but unofficial) as of November 12, 2026. Rules change, so confirm anything important at ecfr.gov. This page is a plain-language guide from the Corridor H Amateur Radio Association, not legal advice.