General Study Guide

General Class Study Guide

All 423 current questions from the 2023–2027 General (Element 3) question pool, with each correct answer and an explanation.

G1A01

On which HF and/or MF amateur bands are there portions where General class licensees cannot transmit?

80 meters, 40 meters, 20 meters, and 15 meters

ExplanationOn these four bands a slice is reserved for Amateur Extra licensees. The other HF/MF bands are fully open to General class.

G1A02

On which of the following bands is phone operation prohibited?

30 meters

ExplanationThe 30-meter band is limited to CW and narrow digital modes. Voice is not allowed there.

G1A03

On which of the following bands is image transmission prohibited?

30 meters

ExplanationImage modes such as slow-scan TV and fax are also not allowed on 30 meters.

G1A05

On which of the following frequencies are General class licensees prohibited from operating as control operator?

7.125 MHz to 7.175 MHz

ExplanationThat part of 40 meters is reserved for Amateur Extra. A General licensee can’t be the control operator there.

G1A06

Which of the following applies when the FCC rules designate the amateur service as a secondary user on a band?

Amateur stations must not cause harmful interference to primary users and must accept interference from primary users

Explanation“Secondary” means hams share the band but have to stay out of the way of the main (primary) users.

G1A07

On which amateur frequencies in the 10-meter band may stations with a General class control operator transmit CW emissions?

The entire band

ExplanationOn 10 meters, General licensees can use the whole band for CW (Morse code).

G1A08

Which HF bands have segments exclusively allocated to Amateur Extra licensees?

80 meters, 40 meters, 20 meters, and 15 meters

ExplanationThese four bands each have a section only Extra class operators may use.

G1A09

Which of the following frequencies is within the General class portion of the 15-meter band?

21300 kHz

ExplanationGeneral class privileges on 15 meters start at 21.275 MHz, so 21.300 MHz (21300 kHz) is inside.

G1A10

What portion of the 10-meter band is available for repeater use?

The portion above 29.5 MHz

Explanation10-meter repeaters are allowed only in the top part of the band, above 29.5 MHz.

G1A11

When General class licensees are not permitted to use the entire voice portion of a band, which portion of the voice segment is available to them?

The upper frequency portion

ExplanationExtra class gets the lower part of the voice segment. General class gets the upper part.

G1B01

What is the maximum height above ground for an antenna structure not near a public use airport without requiring notification to the FAA and registration with the FCC?

200 feet

ExplanationTaller structures need FAA notification and FCC registration. Up to 200 feet doesn’t, unless you are near an airport.

G1B02

With which of the following conditions must beacon stations comply?

No more than one beacon station may transmit in the same band from the same station location

ExplanationA beacon is an unattended station that repeats its call sign so people can check propagation. You are allowed only one per band at a location.

G1B03

Which of the following is a purpose of a beacon station as identified in the FCC rules?

Observation of propagation and reception

ExplanationBeacons exist so operators can tell which bands are open and how well signals are being received.

G1B04

Which of the following transmissions is permitted for all amateur stations?

Occasional retransmission of weather and propagation forecast information from US government stations

ExplanationOccasionally relaying government weather or propagation bulletins is allowed. Regular rebroadcasting is not.

G1B05

Which of the following one-way transmissions are permitted?

Transmissions to assist with learning the International Morse code

ExplanationOne-way transmissions are normally banned, but code practice transmissions are an allowed exception.

G1B06

Under what conditions are state and local governments permitted to regulate amateur radio antenna structures?

Amateur Service communications must be reasonably accommodated, and regulations must constitute the minimum practical to accommodate a legitimate purpose of the state or local entity

ExplanationUnder the FCC’s PRB-1 policy, local rules can’t ban ham antennas. They must allow reasonable amateur communication with the least restriction needed.

G1B07

What are the restrictions on the use of abbreviations or procedural signals in the amateur service?

They may be used if they do not obscure the meaning of a message

ExplanationAbbreviations like “73” and Q signals are fine as long as they don’t hide what you mean.

G1B08

When is it permissible to communicate with amateur stations in countries outside the areas administered by the Federal Communications Commission?

When the contact is with amateurs in any country except those whose administrations have notified the ITU that they object to such communications

ExplanationYou may talk to hams in other countries unless that country has told the ITU it objects.

G1B09

On what HF frequencies are automatically controlled beacons permitted?

28.20 MHz to 28.30 MHz

ExplanationAutomatically controlled HF beacons live only in this small slice of the 10-meter band.

G1B10

What is the power limit for beacon stations?

100 watts PEP output

ExplanationA beacon may use no more than 100 watts PEP.

G1B11

Who or what determines “good engineering and good amateur practice,” as applied to the operation of an amateur station in all respects not covered by the Part 97 rules?

The FCC

ExplanationWhere the written rules are silent, the FCC decides what counts as good practice.

G1C01

What is the maximum transmitter power an amateur station may use on 10.140 MHz?

200 watts PEP output

ExplanationThe 30-meter band has a special limit of 200 watts PEP, lower than most other bands.

G1C02

What is the maximum transmitter power an amateur station may use on the 12-meter band?

1500 watts PEP output

Explanation12 meters follows the standard limit of 1500 watts PEP.

G1C03

What is the maximum bandwidth permitted by FCC rules for amateur radio stations transmitting on USB frequencies in the 60-meter band?

2.8 kHz

ExplanationOn 60 meters, you may use only specific channels, and signals can be no wider than 2.8 kHz.

G1C04

Which of the following is required by the FCC rules when operating in the 60-meter band?

If you are using an antenna other than a dipole, you must keep a record of the gain of your antenna

Explanation60 meters limits your effective radiated power, so if your antenna isn’t a simple dipole you must record its gain.

G1C05

What is the limit for transmitter power on the 28 MHz band for a General Class control operator?

1500 watts PEP output

ExplanationThe standard limit of 1500 watts PEP applies on 10 meters.

G1C06

What is the limit for transmitter power on the 1.8 MHz band?

1500 watts PEP output

ExplanationOn 160 meters (1.8 MHz) the limit is 1500 watts PEP.

G1C07

What must be done before using a new digital protocol on the air?

Publicly document the technical characteristics of the protocol

ExplanationBefore a new digital mode goes on the air, its technical details must be published so others can decode it.

G1C11

What measurement is specified by FCC rules that regulate maximum power?

PEP output from the transmitter

ExplanationThe rules measure peak envelope power (PEP) at the transmitter output, not at the antenna.

G1D01

Who may receive partial credit for the elements represented by an expired amateur radio license?

Any person who can demonstrate that they once held an FCC-issued General, Advanced, or Amateur Extra class license that was not revoked by the FCC

ExplanationIf you once held one of these licenses and it was not revoked, you can get credit for the exam elements you already passed.

G1D02

What license examinations may you administer as an accredited Volunteer Examiner holding a General class operator license?

Technician only

ExplanationA VE (Volunteer Examiner) with a General license can give only Technician exams. Giving higher exams takes a higher class.

G1D03

On which of the following band segments may you operate if you are a Technician class operator and have an unexpired Certificate of Successful Completion of Examination (CSCE) for General class privileges?

On any General or Technician class band segment

ExplanationA valid CSCE lets you use General privileges right away, before the FCC posts your upgrade.

G1D04

Who must observe the administration of a Technician class license examination?

At least three Volunteer Examiners of General class or higher

ExplanationEvery exam session needs three VEs. For a Technician exam, all three must be General or higher.

G1D05

When operating a US station by remote control from outside the country, what license is required of the control operator?

A US operator/primary station license

ExplanationIf you control a US station from abroad, you still need your U.S. license.

G1D06

Until an upgrade to General class is shown in the FCC database, when must a Technician licensee identify with “AG” after their call sign?

Whenever they operate using General class frequency privileges

ExplanationWhile you wait for the FCC to post your upgrade, add “AG” after your call sign whenever you use General privileges.

G1D07

Volunteer Examiners are accredited by what organization?

A Volunteer Examiner Coordinator

ExplanationA VEC (Volunteer Examiner Coordinator) is the group that accredits VEs, not the FCC directly.

G1D08

Which of the following criteria must be met for a non-US citizen to be an accredited Volunteer Examiner?

The person must hold an FCC granted amateur radio license of General class or above

ExplanationCitizenship doesn’t matter. The examiner must hold a U.S. license of General class or higher.

G1D09

How long is a Certificate of Successful Completion of Examination (CSCE) valid for exam element credit?

365 days

ExplanationA CSCE is proof you passed an exam element, and it’s good for one year.

G1D10

What is the minimum age that one must be to qualify as an accredited Volunteer Examiner?

18 years

ExplanationYou must be at least 18 to be a Volunteer Examiner.

G1D11

What action is required to obtain a new General class license after a previously held license has expired and the two-year grace period has passed?

The applicant must show proof of the appropriate expired license grant and pass the current Element 2 exam

ExplanationAfter the grace period you must re-test Technician (Element 2). You then get credit for the expired license.

G1D12

When operating a station in South America by remote control over the internet from the US, what regulations apply?

Only those of the remote station’s country

ExplanationThe rules follow the location of the station you are controlling, not where you are sitting.

G1E01

Which of the following would disqualify a third party from participating in sending a message via an amateur station?

The third party’s amateur license has been revoked and not reinstated

ExplanationA third party is someone else who takes part in the conversation. A person whose license was revoked may not take part.

G1E02

When may a 10-meter repeater retransmit the 2-meter signal from a station that has a Technician class control operator?

Only if the 10-meter repeater control operator holds at least a General class license

ExplanationTechnicians can’t use most of 10 meters for voice. The repeater’s control operator must have at least a General license.

G1E03

What is required to conduct communications with a digital station operating under automatic control outside the automatic control band segments?

The station initiating the contact must be under local or remote control

ExplanationAutomatic digital stations outside their usual segments may only be contacted by a station that has a person in control.

G1E04

Which of the following conditions require a licensed amateur radio operator to take specific steps to avoid harmful interference to other users or facilities?

All these choices are correct

ExplanationBe extra careful near an FCC Monitoring Station, on bands where hams are secondary users, and when using spread spectrum.

G1E05

What are the restrictions on messages sent to a third party in a country with which there is a Third-Party Agreement?

They must relate to amateur radio, or remarks of a personal character, or messages relating to emergencies or disaster relief

ExplanationThird-party messages to other countries are limited to ham radio topics, personal remarks, or emergency messages.

G1E06

The frequency allocations of which ITU region apply to radio amateurs operating in North and South America?

Region 2

ExplanationThe ITU divides the world into three regions. North and South America are Region 2.

G1E07

In what part of the 2.4 GHz band may an amateur station communicate with non-licensed Wi-Fi stations?

No part

ExplanationHams may not talk to Wi-Fi stations. Amateur traffic must be between licensed hams.

G1E08

What is the maximum PEP output allowed for spread spectrum transmissions?

10 watts

ExplanationSpread spectrum is a signal-spreading technique. Hams are limited to 10 watts PEP when using it.

G1E10

Why should an amateur operator normally avoid transmitting on 14.100, 18.110, 21.150, 24.930 and 28.200 MHz?

A system of propagation beacon stations operates on those frequencies

ExplanationThese are the frequencies of the worldwide beacon network. Transmitting there blocks the signals people use to check band conditions.

G1E11

On what bands may automatically controlled stations transmitting RTTY or data emissions communicate with other automatically controlled digital stations?

Anywhere in the 6-meter or shorter wavelength bands, and in limited segments of some of the HF bands

ExplanationAutomatic digital stations can operate on 6 meters and above, plus small segments of some HF bands.

G1E12

When may third-party messages be transmitted via remote control?

Under any circumstances in which third party messages are permitted by FCC rules

ExplanationRemote control doesn’t change the rules. If a third-party message is allowed, it is allowed by remote control too.

G2A01

Which mode is most commonly used for voice communications on frequencies of 14 MHz or higher?

Upper sideband

ExplanationBy long-standing custom, hams use upper sideband (USB) on 20 meters and above.

G2A02

Which mode is most commonly used for voice communications on the 160-, 75-, and 40-meter bands?

Lower sideband

ExplanationLower sideband (LSB) is the convention on these lower HF bands.

G2A03

Which mode is most commonly used for SSB voice communications in the VHF and UHF bands?

Upper sideband

ExplanationOn VHF and UHF, SSB voice is normally upper sideband.

G2A04

Which mode is most commonly used for voice communications on the 17- and 12-meter bands?

Upper sideband

ExplanationLike 20 meters and up, 17 and 12 meters use upper sideband.

G2A05

Which mode of voice communication is most commonly used on the HF amateur bands?

Single sideband

ExplanationSSB sends just one half of the signal, so it travels farther with the same power.

G2A06

Which of the following is an advantage of using single sideband, as compared to other analog voice modes on the HF amateur bands?

Less bandwidth used and greater power efficiency

ExplanationSSB takes up less room on the band and puts all its power into the voice.

G2A07

Which of the following statements is true of single sideband (SSB)?

Only one sideband is transmitted; the other sideband and carrier are suppressed

ExplanationSSB keeps one sideband and removes the other sideband and the carrier to save power and space.

G2A08

What is the recommended way to break into a phone contact?

Say your call sign once

ExplanationTo join a conversation, simply say your call sign once and wait to be recognized.

G2A09

Why do most amateur stations use lower sideband on the 160-, 75-, and 40-meter bands?

It is commonly accepted amateur practice

ExplanationThere is no rule. Everyone uses LSB there so signals line up.

G2A10

Which of the following statements is true of VOX operation versus PTT operation?

It allows “hands free” operation

ExplanationVOX starts transmitting when you speak. PTT means push-to-talk with a button.

G2A11

Generally, who should respond to a station in the contiguous 48 states calling “CQ DX”?

Any stations outside the lower 48 states

ExplanationDX means distant stations. A “CQ DX” call is asking for contacts from outside the lower 48 states.

G2A12

What control is typically adjusted for proper ALC setting on a single sideband transceiver?

Transmit audio or microphone gain

ExplanationALC (automatic level control) prevents overdriving the transmitter. Set it with your mic gain.

G2B01

Which of the following is true concerning access to frequencies?

Except during emergencies, no amateur station has priority access to any frequency

ExplanationNo one owns a frequency. Emergencies are the only exception.

G2B02

What is the first thing you should do if you are communicating with another amateur station and hear a station in distress break in?

Acknowledge the station in distress and determine what assistance may be needed

ExplanationA distress call comes first. Answer it and find out what help is needed.

G2B03

What is good amateur practice if propagation changes during a contact creating interference from other stations using the frequency?

Attempt to resolve the interference problem with the other stations in a mutually acceptable manner

ExplanationWork it out politely. Nobody has priority.

G2B04

When selecting a CW transmitting frequency, what minimum separation from other stations should be used to minimize interference to stations on adjacent frequencies?

150 Hz to 500 Hz

ExplanationCW signals are narrow, so a small gap is enough.

G2B05

When selecting an SSB transmitting frequency, what minimum separation should be used to minimize interference to stations on adjacent frequencies?

2 kHz to 3 kHz

ExplanationAn SSB voice signal is about 3 kHz wide, so allow 2 to 3 kHz of space.

G2B06

How can you avoid harmful interference on an apparently clear frequency before calling CQ on CW or phone?

Send “QRL?” on CW, followed by your call sign; or, if using phone, ask if the frequency is in use, followed by your call sign

ExplanationThe frequency may be in use by a station you can’t hear. Ask first.

G2B07

Which of the following complies with commonly accepted amateur practice when choosing a frequency on which to initiate a call?

Follow the voluntary band plan

ExplanationA band plan is an agreed guide for which modes go where on a band.

G2B08

What is the voluntary band plan restriction for US stations transmitting within the 48 contiguous states in the 50.1 MHz to 50.125 MHz band segment?

Only contacts with stations not within the 48 contiguous states

ExplanationThis 6-meter segment is kept for long-distance (DX) contacts, so don’t use it for local contacts.

G2B09

Who may be the control operator of an amateur station transmitting in RACES to assist relief operations during a disaster?

Only a person holding an FCC-issued amateur operator license

ExplanationRACES is the government-linked emergency service for hams. Control operators must still hold an FCC ham license.

G2B10

Which of the following is good amateur practice for net management?

Have a backup frequency in case of interference or poor conditions

ExplanationA net is an organized on-air meeting. Plan an alternate frequency in case the main one fails.

G2B11

How often may RACES training drills and tests be routinely conducted without special authorization?

No more than 1 hour per week

ExplanationRACES drills are limited to one hour a week unless special permission is given.

G2C01

Which of the following describes full break-in CW operation (QSK)?

Transmitting stations can receive between code characters and elements

ExplanationWith QSK, your receiver listens between dots and dashes, so the other station can interrupt you.

G2C02

What should you do if a CW station sends “QRS?”

Send slower

ExplanationQRS means “slow down.” Reducing speed is the polite response.

G2C03

What does it mean when a CW operator sends “KN” at the end of a transmission?

Listening only for a specific station or stations

ExplanationKN means “go ahead, but only the station I named.” Others shouldn’t call.

G2C04

What does the Q signal “QRL?” mean?

“Are you busy?” or “Is this frequency in use?”

ExplanationQ signals are three-letter codes. QRL? asks whether the frequency is in use. QRL without a question mark means “I am busy.”

G2C05

What is the best speed to use when answering a CQ in Morse code?

The fastest speed at which you are comfortable copying, but no faster than the CQ

ExplanationMatch their speed or go slower. Don’t send faster than the station that called.

G2C06

What does the term “zero beat” mean in CW operation?

Matching the transmit frequency to the frequency of a received signal

ExplanationYou tune your radio until the tone drops to nothing, so you are on the same frequency as the other station.

G2C07

When sending CW, what does a “C” mean when added to the RST report?

Chirpy or unstable signal

ExplanationRST reports readability, strength, and tone. A “C” at the end says the tone chirps.

G2C08

What prosign is sent to indicate the end of a formal message when using CW?

AR

ExplanationProsigns are Morse shortcuts. AR means “end of message.”

G2C09

What does the Q signal “QSL” mean?

I have received and understood

ExplanationQSL means “I got it.” Hams also swap QSL cards to confirm contacts.

G2C10

What does the Q signal “QRN” mean?

I am troubled by static

ExplanationQRN is natural noise such as static. QRM is interference from other stations.

G2C11

What does the Q signal “QRV” mean?

I am ready to receive

ExplanationQRV means “I am ready.”

G2D01

What is the Volunteer Monitor Program?

Amateur volunteers who are formally enlisted to monitor the airwaves for rules violations

ExplanationVolunteer Monitors listen for rule-breaking and help the FCC and the ham community address it.

G2D02

Which of the following are objectives of the Volunteer Monitor Program?

To encourage amateur radio operators to self-regulate and comply with the rules

ExplanationThe goal is to help hams police themselves and follow the rules.

G2D03

What procedure may be used by Volunteer Monitors to localize a station whose continuous carrier is holding a repeater on in their area?

Compare beam headings on the repeater input from their home locations with that of other Volunteer Monitors

ExplanationSeveral monitors point their antennas at the signal and compare directions. Where the lines cross is the likely location.

G2D04

Which of the following describes an azimuthal projection map?

A map that shows true bearings and distances from a specific location

ExplanationAzimuthal maps are centered on your location so a straight line gives the true direction to point your antenna.

G2D05

Which of the following indicates that you are looking for an HF contact with any station?

Repeat “CQ” a few times, followed by “this is,” then your call sign a few times, then pause to listen, repeat as necessary

ExplanationCQ means you want a contact with anyone. Say it a few times, give your call sign, and listen.

G2D06

How is a directional antenna pointed when making a “long-path” contact with another station?

180 degrees from the station’s short-path heading

ExplanationThe signal goes the long way around the world, which is exactly the opposite direction of the short path.

G2D07

Which of the following are examples of the NATO Phonetic Alphabet?

Alpha, Bravo, Charlie, Delta

ExplanationThe NATO alphabet is the standard word list for spelling letters on the air.

G2D08

Why do many amateurs keep a station log?

To help with a reply if the FCC requests information about your station

ExplanationThe FCC doesn’t require a log in most cases, but a log helps you answer questions about your operation.

G2D09

Which of the following is required when participating in a contest on HF frequencies?

Identify your station according to normal FCC regulations

ExplanationContests don’t change the rules. You still must give your call sign as usual.

G2D10

What is QRP operation?

Low-power transmit operation

ExplanationQRP means running low power, commonly 5 watts or less.

G2D11

Why are signal reports typically exchanged at the beginning of an HF contact?

To allow each station to operate according to conditions

ExplanationThe report tells each side how well they’re being heard, so they can adjust power or mode.

G2E01

Which mode is normally used when sending RTTY signals via AFSK with an SSB transmitter?

LSB

ExplanationRTTY is radioteletype. When done with audio tones through an SSB radio, lower sideband is the usual choice.

G2E02

What is VARA?

A digital protocol used with Winlink

ExplanationVARA is a modem protocol for fast data. It is used with Winlink, the radio email system.

G2E03

What symptoms may result from other signals interfering with a PACTOR or VARA transmission?

All these choices are correct

ExplanationInterference causes repeated retries, long pauses, and failed connections.

G2E04

Which of the following is good practice when choosing a transmitting frequency to answer a station calling CQ using FT8?

Find a clear frequency during the alternate time slot to the calling station

ExplanationFT8 alternates time slots. Reply in the other slot on an empty frequency so you don’t talk over them.

G2E05

What is the standard sideband for JT65, JT9, FT4, or FT8 digital signal when using AFSK?

USB

ExplanationThese weak-signal digital modes use upper sideband.

G2E06

What is the most common frequency shift for RTTY emissions in the amateur HF bands?

170 Hz

ExplanationIn RTTY, two tones are 170 Hz apart. That gap is the “shift.”

G2E07

Which of the following is required when using FT8?

Computer time accurate to within approximately 1 second

ExplanationFT8 works in timed slots, so your computer’s clock must be nearly exact.

G2E08

In what segment of the 20-meter band are most digital mode operations commonly found?

Between 14.070 MHz and 14.100 MHz

ExplanationThis is the usual digital area of 20 meters.

G2E09

How do you join a contact between two stations using the PACTOR protocol?

Joining an existing contact is not possible, PACTOR connections are limited to two stations

ExplanationPACTOR is a one-to-one connection, so a third station can’t join.

G2E10

Which of the following is a way to establish contact with a digital messaging system gateway station?

Transmit a connect message on the station’s published frequency

ExplanationGateways publish their frequencies. You send a connect request there.

G2E11

What is the primary purpose of an Amateur Radio Emergency Data Network (AREDN) mesh network?

To provide high-speed data services during an emergency or community event

ExplanationAREDN is a Wi-Fi-style mesh that carries data when normal networks may be down.

G2E12

Which of the following describes Winlink?

All these choices are correct

ExplanationWinlink is a radio email network. It uses packet radio and works on both VHF and HF.

G2E13

What is another name for a Winlink Remote Message Server?

Gateway

ExplanationThe gateway is the station that connects your radio message to the Winlink system.

G2E14

What could be wrong if you cannot decode an RTTY or other FSK signal even though it is apparently tuned in properly?

All these choices are correct

ExplanationReversed mark and space, the wrong baud rate, or the wrong sideband can each garble the decode.

G2E15

Which of the following is a common location for FT8?

Approximately 14.074 MHz to 14.077 MHz

ExplanationOn 20 meters, FT8 is found around 14.074 MHz.

G3A01

How does a higher sunspot number affect HF propagation?

Higher sunspot numbers generally indicate a greater probability of good propagation at higher frequencies

ExplanationMore sunspots mean a more active Sun, which charges the ionosphere more strongly. That helps higher HF bands work.

G3A02

What effect does a sudden ionospheric disturbance have on the daytime ionospheric propagation?

It disrupts signals on lower frequencies more than those on higher frequencies

ExplanationA solar flare can briefly black out the daytime ionosphere, hitting the lower frequencies hardest.

G3A03

Approximately how long does it take the increased ultraviolet and X-ray radiation from a solar flare to affect radio propagation on Earth?

8 minutes

ExplanationLight and X-rays travel at the speed of light, so effects arrive in about 8 minutes.

G3A04

Which of the following are the least reliable bands for long-distance communications during periods of low solar activity?

15 meters, 12 meters, and 10 meters

ExplanationWith little solar activity, the ionosphere can’t reflect these higher bands well.

G3A05

What is the solar flux index?

A measure of solar radiation with a wavelength of 10.7 centimeters

ExplanationThe SFI is a radio-noise reading from the Sun. A higher number usually means better HF conditions.

G3A06

What is a geomagnetic storm?

A temporary disturbance in Earth’s geomagnetic field

ExplanationCharged particles from the Sun disturb Earth’s magnetic field, which can disrupt HF propagation.

G3A07

At what point in the solar cycle does the 20-meter band usually support worldwide propagation during daylight hours?

At any point

Explanation20 meters is dependable in daytime throughout the 11-year sunspot cycle.

G3A08

How can a geomagnetic storm affect HF propagation?

Degrade high-latitude HF propagation

ExplanationStorms hurt paths that cross the polar regions most.

G3A09

How can high geomagnetic activity benefit radio communications?

Creates auroras that can reflect VHF signals

ExplanationAuroras can bounce VHF signals, allowing contacts that are normally not possible.

G3A10

What causes HF propagation conditions to vary periodically in a 26- to 28-day cycle?

Rotation of the Sun’s surface layers around its axis

ExplanationAs the Sun rotates about once a month, active regions face Earth and then turn away.

G3A11

How long does it take a coronal mass ejection to affect radio propagation on Earth?

15 hours to several days

ExplanationA coronal mass ejection is a cloud of particles. They travel slower than light, so they take hours to days.

G3A12

What does the K-index measure?

The short-term stability of Earth’s geomagnetic field

ExplanationThe K-index is a quick (3-hour) reading of how disturbed the geomagnetic field is.

G3A13

What does the A-index measure?

The long-term stability of Earth’s geomagnetic field

ExplanationThe A-index is a daily summary of geomagnetic stability.

G3A14

How is long distance radio communication usually affected by the charged particles that reach Earth from solar coronal holes?

HF communication is disturbed

ExplanationParticles streaming from coronal holes disturb the ionosphere and degrade HF.

G3B01

What is a characteristic of skywave signals arriving at your location by both short-path and long-path propagation?

A slightly delayed echo might be heard

ExplanationThe long path takes extra time, so you hear the same signal twice, slightly offset.

G3B02

What factors affect the MUF?

All these choices are correct

ExplanationThe MUF (Maximum Usable Frequency) depends on the path, the time of day and season, and solar activity.

G3B03

Which frequency will have the least attenuation for long-distance skip propagation?

Just below the MUF

ExplanationSignals just below the MUF are bent back to Earth and lose the least energy on the way.

G3B04

Which of the following is a way to determine current propagation on a desired band from your station?

Use a network of automated receiving stations on the internet to see where your transmissions are being received

ExplanationSites like PSK Reporter show who is hearing you right now.

G3B05

How does the ionosphere affect radio waves with frequencies below the MUF and above the LUF?

They are refracted back to Earth

ExplanationBetween the LUF and MUF, signals bend back down and can be heard far away.

G3B06

What usually happens to radio waves with frequencies below the LUF?

They are attenuated before reaching the destination

ExplanationBelow the LUF (Lowest Usable Frequency) the D region absorbs the signal.

G3B07

What does LUF stand for?

The Lowest Usable Frequency for communications between two specific points

ExplanationLUF is the lowest frequency that will still make it between two points.

G3B08

What does MUF stand for?

The Maximum Usable Frequency for communications between two points

ExplanationMUF is the highest frequency that will bend back to Earth between two points.

G3B09

What is the approximate maximum distance along the Earth’s surface normally covered in one hop using the F2 region?

2,500 miles

ExplanationThe F2 region is the highest, so a single hop covers the most ground.

G3B10

What is the approximate maximum distance along the Earth’s surface normally covered in one hop using the E region?

1,200 miles

ExplanationThe E region is lower, so one hop covers about half the F2 distance.

G3B11

What happens to HF propagation when the LUF exceeds the MUF?

Propagation via ordinary skywave communications is not possible over that path

ExplanationIf the lowest usable frequency is above the highest usable one, no frequency works.

G3B12

Which of the following is typical of the lower HF frequencies during the summer?

High levels of atmospheric noise or static

ExplanationSummer thunderstorms create lots of static on the lower bands.

G3C01

Which ionospheric region is closest to the surface of Earth?

The D region

ExplanationThe layers from lowest to highest are D, E, F1, and F2.

G3C02

What is meant by the term “critical frequency” at a given incidence angle?

The highest frequency which is refracted back to Earth

ExplanationAnything above the critical frequency passes through into space.

G3C03

Why is skip propagation via the F2 region longer than that via the other ionospheric regions?

Because it is the highest

ExplanationThe higher the layer, the farther each hop reaches.

G3C04

What does the term “critical angle” mean, as applied to radio wave propagation?

The highest takeoff angle that will return a radio wave to Earth under specific ionospheric conditions

ExplanationSignals aimed higher than the critical angle escape into space.

G3C05

Why is long-distance communication on the 40-, 60-, 80-, and 160-meter bands more difficult during the day?

The D region absorbs signals at these frequencies during daylight hours

ExplanationThe D region only exists in daylight and soaks up lower-frequency signals.

G3C06

What is a characteristic of HF scatter?

Signals have a fluttering sound

ExplanationScattered signals arrive through many paths, which makes them sound fluttery.

G3C07

What makes HF scatter signals often sound distorted?

Energy is scattered into the skip zone through several different paths

ExplanationCopies of the signal arrive at slightly different times and blend together.

G3C08

Why are HF scatter signals in the skip zone usually weak?

Only a small part of the signal energy is scattered into the skip zone

ExplanationThe skip zone is the area where you normally can’t hear a signal. Only a little energy scatters back into it.

G3C09

What type of propagation allows signals to be heard in the transmitting station’s skip zone?

Scatter

ExplanationScatter puts weak signals into the skip zone.

G3C10

What is near vertical incidence skywave (NVIS) propagation?

Short distance MF or HF propagation at high elevation angles

ExplanationNVIS sends signals nearly straight up so they come down within a few hundred miles. It is good for regional communication.

G3C11

Which ionospheric region is the most absorbent of signals below 10 MHz during daylight hours?

The D region

ExplanationThe D region soaks up lower HF signals during the day.

G4A01

What is the purpose of the notch filter found on many HF transceivers?

To reduce interference from carriers in the receiver passband

ExplanationA notch filter removes one narrow tone, such as a steady carrier, without affecting nearby signals.

G4A02

What is the benefit of using the opposite or “reverse” sideband when receiving CW?

It may be possible to reduce or eliminate interference from other signals

ExplanationSwitching sidebands moves the interfering signal to the other side of your signal, where filters can remove it.

G4A03

How does a noise blanker work?

By reducing receiver gain during a noise pulse

ExplanationThe blanker briefly mutes the receiver when it detects a sharp pulse of noise.

G4A04

What is the effect on plate current of the correct setting of a vacuum-tube RF power amplifier’s TUNE control?

A pronounced dip

ExplanationWhen tuned correctly, the amplifier’s plate current falls sharply.

G4A05

Why is automatic level control (ALC) used with an RF power amplifier?

To prevent excessive drive

ExplanationALC limits the signal going into the amplifier so it isn’t overdriven and distorted.

G4A06

What is the purpose of an antenna tuner?

Increase power transfer from the transmitter to the feed line

ExplanationA tuner makes the antenna system look like 50 ohms to the radio so more power goes out.

G4A07

What happens as a receiver’s noise reduction control level is increased?

Received signals may become distorted

ExplanationHeavy noise reduction also removes some of the wanted signal.

G4A08

What is the correct adjustment for the LOAD or COUPLING control of a vacuum tube RF power amplifier?

Desired power output without exceeding maximum allowable plate current

ExplanationSet the load for the output you want, staying within the tube’s limit.

G4A09

What is the purpose of delaying RF output after activating a transmitter’s keying line to an external amplifier?

To allow time for the amplifier to switch the antenna between the transceiver and the amplifier output

ExplanationThe relay needs a moment to flip. Without a delay you’d send RF through a switching relay.

G4A10

What is the function of an electronic keyer?

Automatic generation of dots and dashes for CW operation

ExplanationA keyer produces correctly timed Morse code from paddle presses.

G4A11

Why should the ALC system be inactive when transmitting AFSK data signals?

The ALC action distorts the signal

ExplanationALC squashes the signal and damages digital tones. Set drive so ALC does not act.

G4A12

Which of the following is a common use of the dual-VFO feature on a transceiver?

To transmit on one frequency and listen on another

ExplanationDual VFOs let you work “split,” such as listening to a DX station while calling on a different frequency.

G4A13

What is the purpose of using a receive attenuator?

To prevent receiver overload from strong incoming signals

ExplanationThe attenuator weakens everything so a very strong signal doesn’t overload the front end.

G4B01

What item of test equipment contains horizontal and vertical channel amplifiers?

An oscilloscope

ExplanationA scope draws a signal’s shape across the screen, using one amplifier for each axis.

G4B02

Which of the following is an advantage of an oscilloscope versus a digital voltmeter?

Complex waveforms can be measured

ExplanationA scope shows the shape of a signal, while a voltmeter gives only a number.

G4B03

Which of the following is the best instrument to use for checking the keying waveform of a CW transmitter?

An oscilloscope

ExplanationSeeing the rise and fall of each dot helps you catch key clicks.

G4B04

What signal source is connected to the vertical input of an oscilloscope when checking the RF envelope pattern of a transmitted signal?

The attenuated RF output of the transmitter

ExplanationYou feed a weakened sample of the transmitter’s output to the scope.

G4B05

Why do voltmeters have high input impedance?

It decreases the loading on circuits being measured

ExplanationA meter that draws little current won’t change the circuit it measures.

G4B06

What is an advantage of a digital multimeter as compared to an analog multimeter?

Higher precision

ExplanationA digital meter gives exact numerical readings.

G4B07

What signals are used to conduct a two-tone test?

Two non-harmonically related audio signals

ExplanationA two-tone test feeds two unrelated audio tones into an SSB transmitter.

G4B08

What transmitter performance parameter does a two-tone test analyze?

Linearity

ExplanationIt shows whether the transmitter amplifies cleanly without creating extra signals.

G4B09

When is an analog multimeter preferred to a digital multimeter?

When adjusting circuits for maximum or minimum values

ExplanationA moving needle is easier to watch than changing digits when you’re tuning for a peak or dip.

G4B10

Which of the following can be determined with a directional wattmeter?

Standing wave ratio

ExplanationA directional wattmeter reads forward and reflected power. From those you can calculate SWR.

G4B11

Which of the following must be connected to an antenna analyzer when it is being used for SWR measurements?

Antenna and feed line

ExplanationThe analyzer makes its own test signal, so only the antenna system is connected, not a transmitter.

G4B12

What effect can strong signals from nearby transmitters have on an antenna analyzer?

Received power that interferes with SWR readings

ExplanationStrong outside signals leak in and spoil the measurement.

G4B13

Which of the following can be measured with an antenna analyzer?

Impedance of coaxial cable

ExplanationAn analyzer can measure impedance and SWR, but not antenna gain or transmitter power.

G4C01

Which of the following might be useful in reducing RF interference to audio frequency circuits?

Bypass capacitor

ExplanationA bypass capacitor sends stray RF to ground while letting audio through.

G4C02

Which of the following could be a cause of interference covering a wide range of frequencies?

Arcing at a poor electrical connection

ExplanationA spark from a bad connection creates broadband noise.

G4C03

What sound is heard from an audio device experiencing RF interference from a single sideband phone transmitter?

Distorted speech

ExplanationSSB interference sounds like garbled voice.

G4C04

What sound is heard from an audio device experiencing RF interference from a CW transmitter?

On-and-off humming or clicking

ExplanationCW is keyed on and off, so the interference thumps with the code.

G4C05

What is a possible cause of high voltages that produce RF burns?

The ground wire has high impedance on that frequency

ExplanationIf the ground is poor at RF, voltage builds up on equipment and can burn you.

G4C06

What is a possible effect of a resonant ground connection?

High RF voltages on the enclosures of station equipment

ExplanationA ground wire that is resonant at your frequency doesn’t work as a ground. RF voltage appears on equipment cases.

G4C07

Why should soldered joints not be used in lightning protection ground connections?

A soldered joint will likely be destroyed by the heat of a lightning strike

ExplanationSolder melts at low temperatures. Use clamps or bolted connections.

G4C08

Which of the following would reduce RF interference caused by common-mode current on an audio cable?

Place a ferrite choke on the cable

ExplanationA ferrite choke blocks RF current flowing along the outside of the cable.

G4C09

How can the effects of ground loops be minimized?

Bond equipment enclosures together

ExplanationConnecting all the equipment together keeps them at the same potential and stops hum.

G4C10

What could be a symptom caused by a ground loop in your station’s audio connections?

You receive reports of “hum” on your station’s transmitted signal

ExplanationA ground loop adds a 60 Hz hum to the audio.

G4C11

What technique helps to minimize RF “hot spots” in an amateur station?

Bonding all equipment enclosures together

ExplanationJoining all cases removes voltage differences where RF could build up.

G4C12

Why must all metal enclosures of station equipment be grounded?

It ensures that hazardous voltages cannot appear on the chassis

ExplanationA good ground carries a fault current away so the case never becomes live.

G4D01

What is the purpose of a speech processor in a transceiver?

Increase the apparent loudness of transmitted voice signals

ExplanationThe processor raises your average voice level so the signal sounds stronger.

G4D02

How does a speech processor affect a single sideband phone signal?

It increases average power

ExplanationPeak power stays the same, but the average goes up.

G4D03

What is the effect of an incorrectly adjusted speech processor?

All these choices are correct

ExplanationToo much processing causes distortion, extra interference products, and more background noise.

G4D04

What does an S meter measure?

Received signal strength

ExplanationThe S meter shows how strong a signal is at your receiver.

G4D05

How does a signal that reads 20 dB over S9 compare to one that reads S9 on a receiver, assuming a properly calibrated S meter?

It is 100 times more powerful

ExplanationEvery 10 dB is a tenfold power increase. So 20 dB is 10 × 10 = 100.

G4D06

How much change in signal strength is typically represented by one S unit?

6 dB

ExplanationOne S unit equals 6 dB, which is a four-fold power change.

G4D07

How much must the power output of a transmitter be raised to change the S meter reading on a distant receiver from S8 to S9?

Approximately 4 times

ExplanationOne S unit is 6 dB, which equals about 4 times the power.

G4D08

What frequency range is occupied by a 3 kHz LSB signal when the displayed carrier frequency is set to 7.178 MHz?

7.175 MHz to 7.178 MHz

ExplanationOn LSB the signal extends below the displayed frequency.

G4D09

What frequency range is occupied by a 3 kHz USB signal with the displayed carrier frequency set to 14.347 MHz?

14.347 MHz to 14.350 MHz

ExplanationOn USB the signal extends above the displayed frequency.

G4D10

How close to the lower edge of a band’s phone segment should your displayed carrier frequency be when using 3 kHz wide LSB?

At least 3 kHz above the edge of the segment

ExplanationLSB extends downward, so keep the carrier 3 kHz above the lower edge to stay inside.

G4D11

How close to the upper edge of a band’s phone segment should your displayed carrier frequency be when using 3 kHz wide USB?

At least 3 kHz below the edge of the band

ExplanationUSB extends upward, so keep the carrier 3 kHz below the upper edge.

G4E01

What is the purpose of a capacitance hat on a mobile antenna?

To electrically lengthen a physically short antenna

ExplanationThe hat adds capacitance, making a short antenna act longer.

G4E02

What is the purpose of a corona ball on an HF mobile antenna?

To reduce RF voltage discharge from the tip of the antenna while transmitting

ExplanationThe tip of a whip has high RF voltage. A ball there prevents sparking and corona discharge.

G4E03

Which of the following direct, fused power connections would be the best for a 100-watt HF mobile installation?

To the battery using heavy-gauge wire

ExplanationRun thick, fused wire straight to the battery, where plenty of current is available.

G4E04

Why should DC power for a 100-watt HF transceiver not be supplied by a vehicle’s auxiliary power socket?

The socket’s wiring may be inadequate for the current drawn by the transceiver

ExplanationThese sockets are wired for light loads and can overheat with a 100-watt radio.

G4E05

Which of the following most limits an HF mobile installation?

Efficiency of the electrically short antenna

ExplanationMobile antennas are much shorter than a proper antenna, so they radiate less effectively.

G4E06

What is one disadvantage of using a shortened mobile antenna as opposed to a full-size antenna?

Operating bandwidth may be very limited

ExplanationA short antenna works well over only a narrow range, so you retune when you change frequency.

G4E07

Which of the following may cause receive interference to an HF transceiver installed in a vehicle?

All these choices are correct

ExplanationThe charging system, fuel system, and onboard computers can all create noise.

G4E08

In what configuration are the individual cells in a solar panel connected together?

Series-parallel

ExplanationCells are combined in series for voltage and in parallel for current.

G4E09

What is the approximate open-circuit voltage from a fully illuminated silicon photovoltaic cell?

0.5 VDC

ExplanationOne silicon solar cell produces about half a volt.

G4E10

Why should a series diode be connected between a solar panel and a storage battery that is being charged by the panel?

To prevent discharge of the battery through the panel during times of low or no illumination

ExplanationThe diode stops the battery from draining back through the panel at night.

G4E11

What precaution should be taken when connecting a solar panel to a lithium iron phosphate battery?

The solar panel must have a charge controller

ExplanationA charge controller keeps the battery from being overcharged.

G5A01

What happens when inductive and capacitive reactance are equal in a series LC circuit?

Resonance causes impedance to be very low

ExplanationAt resonance the two reactances cancel each other, leaving only a tiny resistance, so current flows easily.

G5A02

What is reactance?

Opposition to the flow of alternating current caused by capacitance or inductance

ExplanationReactance is how coils and capacitors resist AC. Unlike resistance, it doesn’t turn power into heat.

G5A03

Which of the following is opposition to the flow of alternating current in an inductor?

Reactance

ExplanationAn inductor’s opposition to AC is called inductive reactance.

G5A04

Which of the following is opposition to the flow of alternating current in a capacitor?

Reactance

ExplanationA capacitor’s opposition to AC is called capacitive reactance.

G5A05

How does an inductor react to AC?

As the frequency of the applied AC increases, the reactance increases

ExplanationHigher frequency means more opposition from a coil.

G5A06

How does a capacitor react to AC?

As the frequency of the applied AC increases, the reactance decreases

ExplanationHigher frequency means less opposition from a capacitor. It is the opposite of an inductor.

G5A07

What is the term for the inverse of impedance?

Admittance

ExplanationAdmittance is 1 divided by impedance, and measures how easily current flows.

G5A08

What is impedance?

The ratio of voltage to current

ExplanationImpedance is the total opposition to AC, found by dividing voltage by current.

G5A09

What unit is used to measure reactance?

Ohm

ExplanationReactance, like resistance and impedance, is measured in ohms.

G5A10

Which of the following devices can be used for impedance matching at radio frequencies?

All these choices are correct

ExplanationTransformers, Pi-networks, and lengths of transmission line can all match impedances.

G5A11

What letter is used to represent reactance?

X

ExplanationReactance is shown as X. Impedance is Z, and resistance is R.

G5A12

What occurs in an LC circuit at resonance?

Inductive reactance and capacitive reactance cancel

ExplanationResonance is the frequency where the coil and capacitor effects cancel out.

G5B01

What dB change represents a factor of two increase or decrease in power?

Approximately 3 dB

ExplanationDoubling power adds about 3 dB, and halving removes about 3 dB.

G5B02

How does the total current relate to the individual currents in a circuit of parallel resistors?

It equals the sum of the currents through each branch

ExplanationIn a parallel circuit, current splits among the paths and adds back up to the total.

G5B03

How many watts of electrical power are consumed if 400 VDC is supplied to an 800-ohm load?

200 watts

ExplanationP = E² ÷ R = 400 × 400 ÷ 800 = 200.

G5B04

How many watts of electrical power are consumed by a 12 VDC light bulb that draws 0.2 amperes?

2.4 watts

ExplanationP = E × I = 12 × 0.2 = 2.4.

G5B05

How many watts are consumed when a current of 7.0 milliamperes flows through a 1,250-ohm resistance?

Approximately 61 milliwatts

ExplanationP = I² × R = (0.007)² × 1250 ≈ 0.061 W, or 61 mW.

G5B06

What is the PEP produced by 200 volts peak-to-peak across a 50-ohm dummy load?

100 watts

ExplanationPeak voltage is 100 V. PEP = (0.707 × 100)² ÷ 50 = 100 W.

G5B07

What value of an AC signal produces the same power dissipation in a resistor as a DC voltage of the same value?

The RMS value

ExplanationRMS (root mean square) is the AC value that heats a resistor the same as DC.

G5B08

What is the peak-to-peak voltage of a sine wave with an RMS voltage of 120 volts?

339.4 volts

ExplanationPeak = 120 × 1.414 = 169.7 V. Peak-to-peak is twice that, 339.4 V.

G5B09

What is the RMS voltage of a sine wave with a value of 17 volts peak?

12 volts

ExplanationRMS = peak × 0.707 = 17 × 0.707 ≈ 12 V.

G5B10

What percentage of power loss is equivalent to a loss of 1 dB?

20.6 percent

Explanation1 dB is a power ratio of about 0.794, so about 20.6 percent is lost.

G5B11

What is the ratio of PEP to average power for an unmodulated carrier?

1.00

ExplanationA steady carrier doesn’t vary, so peak and average power are the same.

G5B12

What is the RMS voltage across a 50-ohm dummy load dissipating 1200 watts?

245 volts

ExplanationE = √(P × R) = √(1200 × 50) ≈ 245 V.

G5B13

What is the output PEP of an unmodulated carrier if the average power is 1060 watts?

1060 watts

ExplanationFor an unmodulated carrier, PEP equals average power.

G5B14

What is the output PEP of 500 volts peak-to-peak across a 50-ohm load?

625 watts

ExplanationPeak is 250 V. PEP = (0.707 × 250)² ÷ 50 ≈ 625 W.

G5C01

What causes a voltage to appear across the secondary winding of a transformer when an AC voltage source is connected across its primary winding?

Mutual inductance

ExplanationThe changing magnetic field of the primary induces a voltage in the secondary.

G5C02

What is the output voltage if an input signal is applied to the secondary winding of a 4:1 voltage step-down transformer instead of the primary winding?

The input voltage is multiplied by 4

ExplanationRun backwards, a step-down transformer steps up by the same ratio.

G5C03

What is the total resistance of a 10-, a 20-, and a 50-ohm resistor connected in parallel?

5.9 ohms

Explanation1 ÷ (1/10 + 1/20 + 1/50) ≈ 5.9. Parallel resistance is always less than the smallest one.

G5C04

What is the approximate total resistance of a 100- and a 200-ohm resistor in parallel?

67 ohms

Explanation(100 × 200) ÷ (100 + 200) ≈ 67.

G5C05

Why is the primary winding wire of a voltage step-up transformer usually a larger size than that of the secondary winding?

To accommodate the higher current of the primary

ExplanationA step-up transformer has more current on the primary side, so it needs thicker wire.

G5C06

What is the voltage output of a transformer with a 500-turn primary and a 1500-turn secondary when 120 VAC is applied to the primary?

360 volts

ExplanationThe turns ratio is 3:1, so voltage is 120 × 3 = 360.

G5C07

What transformer turns ratio matches an antenna’s 600-ohm feed point impedance to a 50-ohm coaxial cable?

3.5 to 1

ExplanationTurns ratio is the square root of the impedance ratio: √(600 ÷ 50) = √12 ≈ 3.5.

G5C08

What is the equivalent capacitance of two 5.0-nanofarad capacitors and one 750-picofarad capacitor connected in parallel?

10.750 nanofarads

ExplanationParallel capacitors add: 5 + 5 + 0.75 = 10.75 nF.

G5C09

What is the capacitance of three 100-microfarad capacitors connected in series?

33.3 microfarads

ExplanationIn series, equal capacitors divide: 100 ÷ 3 ≈ 33.3.

G5C10

What is the inductance of three 10-millihenry inductors connected in parallel?

3.3 millihenries

ExplanationEqual inductors in parallel divide: 10 ÷ 3 ≈ 3.3.

G5C11

What is the inductance of a circuit with a 20-millihenry inductor connected in series with a 50-millihenry inductor?

70 millihenries

ExplanationInductors in series add: 20 + 50 = 70.

G5C12

What is the capacitance of a 20-microfarad capacitor connected in series with a 50-microfarad capacitor?

14.3 microfarads

Explanation(20 × 50) ÷ (20 + 50) ≈ 14.3. Series capacitance is less than the smallest one.

G5C13

Which of the following components should be added to a capacitor to increase the capacitance?

A capacitor in parallel

ExplanationParallel capacitors add together, making a bigger total.

G5C14

Which of the following components should be added to an inductor to increase the inductance?

An inductor in series

ExplanationSeries inductors add together, making a bigger total.

G6A01

What is the minimum allowable discharge voltage for maximum life of a standard 12-volt lead-acid battery?

10.5 volts

ExplanationDraining a lead-acid battery below about 10.5 V shortens its life.

G6A02

What is an advantage of batteries with low internal resistance?

High discharge current

ExplanationLow internal resistance lets a battery deliver a lot of current without its voltage dropping.

G6A03

What is the approximate forward threshold voltage of a germanium diode?

0.3 volts

ExplanationA germanium diode starts conducting at about 0.3 V.

G6A04

Which of the following is characteristic of an electrolytic capacitor?

High capacitance for a given volume

ExplanationElectrolytics pack a lot of capacitance into a small can.

G6A05

What is the approximate forward threshold voltage of a silicon junction diode?

0.7 volts

ExplanationSilicon diodes start conducting at about 0.7 V.

G6A06

Why should wire-wound resistors not be used in RF circuits?

The resistor’s inductance could make circuit performance unpredictable

ExplanationA wire-wound resistor is a coil of wire, so it acts like an inductor at RF.

G6A07

What are the operating points for a bipolar transistor used as a switch?

Saturation and cutoff

ExplanationA switch is either fully on (saturation) or fully off (cutoff).

G6A08

Which of the following is characteristic of low voltage ceramic capacitors?

Comparatively low cost

ExplanationCeramic capacitors are cheap and widely used.

G6A09

Which of the following describes MOSFET construction?

The gate is separated from the channel by a thin insulating layer

ExplanationA MOSFET’s gate has an insulating oxide layer under it, so it draws almost no current.

G6A10

Which element of a vacuum tube regulates the flow of electrons between cathode and plate?

Control grid

ExplanationThe control grid works like a valve that regulates electron flow.

G6A11

What happens when an inductor is operated above its self-resonant frequency?

It becomes capacitive

ExplanationAt very high frequencies the stray capacitance of a coil takes over.

G6A12

What is the primary purpose of a screen grid in a vacuum tube?

To reduce grid-to-plate capacitance

ExplanationThe screen grid shields the control grid from the plate, reducing unwanted feedback.

G6B01

What determines the performance of a ferrite core at different frequencies?

The composition, or “mix,” of materials used

ExplanationDifferent ferrite mixes work best at different frequency ranges.

G6B02

What is meant by the term MMIC?

Monolithic Microwave Integrated Circuit

ExplanationAn MMIC is a microwave amplifier or other circuit built on a single chip.

G6B03

Which of the following is an advantage of CMOS integrated circuits compared to TTL integrated circuits?

Low power consumption

ExplanationCMOS chips use very little power.

G6B04

What is a typical upper frequency limit for low SWR operation of 50-ohm BNC connectors?

4 GHz

ExplanationBNC connectors work well up to about 4 GHz.

G6B05

What is an advantage of using a ferrite core toroidal inductor?

All these choices are correct

ExplanationA toroid (donut shape) gives large inductance, can be tuned to a frequency range, and keeps most of its magnetic field inside.

G6B06

What kind of device is an integrated circuit operational amplifier?

Analog

ExplanationAn op-amp works with continuously varying signals, not just on/off signals.

G6B07

Which of the following describes a type N connector?

A moisture-resistant RF connector useful to 10 GHz

ExplanationType N connectors are weatherproof and work up to about 10 GHz.

G6B08

How is an LED biased when emitting light?

Forward biased

ExplanationAn LED lights when current flows through it in the forward direction.

G6B10

How does a ferrite bead or core reduce common-mode RF current on the shield of a coaxial cable?

By creating an impedance in the current’s path

ExplanationThe ferrite makes it hard for RF current to flow along the outside of the cable.

G6B11

What is an SMA connector?

A small threaded connector suitable for signals up to several GHz

ExplanationSMA connectors are small screw-on connectors used for microwave equipment.

G6B12

Which of these connector types is commonly used for low frequency or dc signal connections to a transceiver?

RCA Phono

ExplanationRCA phono plugs are common for audio and DC connections on radios.

G7A01

What is the function of a power supply bleeder resistor?

It discharges the filter capacitors when power is removed

ExplanationThe resistor slowly drains stored charge after power-off so the supply is safe to touch.

G7A02

Which of the following components are used in a power supply filter network?

Capacitors and inductors

ExplanationFilters smooth the pulsing DC from a rectifier using capacitors and coils.

G7A03

Which type of rectifier circuit uses two diodes and a center-tapped transformer?

Full-wave

ExplanationA center-tapped transformer with two diodes uses both halves of the AC cycle.

G7A04

What is characteristic of a half-wave rectifier in a power supply?

Only one diode is required

ExplanationA half-wave rectifier is the simplest type, using just one diode.

G7A05

What portion of the AC cycle is converted to DC by a half-wave rectifier?

180 degrees

ExplanationIt passes only one half of the cycle, which is 180 degrees.

G7A06

What portion of the AC cycle is converted to DC by a full-wave rectifier?

360 degrees

ExplanationA full-wave rectifier uses the entire cycle.

G7A07

What is the output waveform of an unfiltered full-wave rectifier connected to a resistive load?

A series of DC pulses at twice the frequency of the AC input

ExplanationBoth halves of each cycle become pulses, so there are twice as many.

G7A08

Which of the following is characteristic of a switchmode power supply as compared to a linear power supply?

High-frequency operation allows the use of smaller components

ExplanationSwitching at high speed lets the transformer and filters be much smaller and lighter.

G7A09

Which symbol in figure G7-1 represents a field effect transistor?

Symbol 1

ExplanationSymbol 1 is the field effect transistor (FET). It is drawn as a circle with a gate arrow and a channel line.

G7A10

Which symbol in figure G7-1 represents a Zener diode?

Symbol 5

ExplanationSymbol 5 is a Zener diode. Its symbol has a bent bar on the side that points to the voltage supply. Zener diodes are used to regulate voltage.

G7A11

Which symbol in figure G7-1 represents an NPN junction transistor?

Symbol 2

ExplanationSymbol 2 is an NPN transistor. The arrow on the emitter points outward, away from the base.

G7A12

Which symbol in Figure G7-1 represents a solid core transformer?

Symbol 6

ExplanationSymbol 6 is a transformer. Two coils with straight lines between them show a solid core.

G7A13

Which symbol in Figure G7-1 represents a tapped inductor?

Symbol 7

ExplanationSymbol 7 is a tapped inductor, a coil with an extra connection partway along.

G7B01

What is the purpose of neutralizing an amplifier?

To eliminate self-oscillations

ExplanationNeutralizing cancels feedback that would make an amplifier oscillate on its own.

G7B02

Which of these classes of amplifiers has the highest efficiency?

Class C

ExplanationClass C amplifiers conduct for less than half the cycle, wasting the least power as heat.

G7B03

Which of the following describes the function of a two-input AND gate?

Output is high only when both inputs are high

ExplanationAND means both. The output is on only if both inputs are on.

G7B04

In a Class A amplifier, what percentage of the time does the amplifying device conduct?

100%

ExplanationClass A amplifiers are always on. They are the most linear but the least efficient.

G7B05

How many states does a 3-bit binary counter have?

8

ExplanationThree bits have 2 × 2 × 2 = 8 combinations.

G7B06

What is a shift register?

A clocked array of circuits that passes data in steps along the array

ExplanationOn each clock tick, data shifts one position along a chain of memory cells.

G7B07

Which of the following are basic components of a sine wave oscillator?

A filter and an amplifier operating in a feedback loop

ExplanationAn oscillator feeds part of its output back to the input, with a filter picking the frequency.

G7B08

How is the efficiency of an RF power amplifier determined?

Divide the RF output power by the DC input power

ExplanationEfficiency compares the useful power you get out to the power you put in.

G7B09

What determines the frequency of an LC oscillator?

The inductance and capacitance in the tank circuit

ExplanationThe coil and capacitor form a tuned “tank” circuit that sets the frequency.

G7B10

Which of the following describes a linear amplifier?

An amplifier in which the output preserves the input waveform

ExplanationA linear amplifier makes the signal bigger without changing its shape.

G7B11

For which of the following modes is a Class C power stage appropriate for amplifying a modulated signal?

FM

ExplanationFM has constant amplitude, so an efficient but non-linear Class C stage works. SSB and AM need linear amplifiers.

G7C01

What circuit is used to select one of the sidebands from a balanced modulator?

Filter

ExplanationA balanced modulator produces both sidebands. A filter keeps just one.

G7C02

What output is produced by a balanced modulator?

Double-sideband modulated RF

ExplanationIt produces both sidebands with the carrier removed.

G7C03

What is one reason to use an impedance matching transformer at a transmitter output?

To present the desired impedance to the transmitter and feed line

ExplanationThe transformer makes both sides see the impedance they want.

G7C04

How is a product detector used?

Used in a single sideband receiver to extract the modulated signal

ExplanationA product detector mixes in a carrier to recover the audio from an SSB signal.

G7C05

Which of the following is characteristic of a direct digital synthesizer (DDS)?

Variable output frequency with the stability of a crystal oscillator

ExplanationA DDS can be tuned to any frequency and is as stable as a crystal.

G7C06

Which of the following is an advantage of a digital signal processing (DSP) filter compared to an analog filter?

A wide range of filter bandwidths and shapes can be created

ExplanationDSP filters are software, so you can change their shape and width easily.

G7C07

What term specifies a filter’s attenuation inside its passband?

Insertion loss

ExplanationInsertion loss is how much signal a filter removes from the frequencies it is supposed to pass.

G7C08

Which parameter affects receiver sensitivity?

All these choices are correct

ExplanationInput amplifier gain, the noise figure of the input stage, and the demodulator bandwidth all matter.

G7C09

What is the phase difference between the I and Q RF signals that software-defined radio (SDR) equipment uses for modulation and demodulation?

90 degrees

ExplanationI (in-phase) and Q (quadrature) signals are offset by a quarter cycle, 90 degrees.

G7C10

What is an advantage of using I-Q modulation with software-defined radios (SDRs)?

All types of modulation can be created with appropriate processing

ExplanationWith I and Q you can make AM, FM, SSB, or digital signals just by changing the software.

G7C11

Which of these functions is performed by software in a software-defined radio (SDR)?

All these choices are correct

ExplanationIn an SDR, filtering, detection, and modulation are done in software.

G7C12

What is the frequency above which a low-pass filter’s output power is less than half the input power?

Cutoff frequency

ExplanationThe cutoff frequency is where the filter has dropped to half power (3 dB down).

G7C13

What term specifies a filter’s maximum ability to reject signals outside its passband?

Ultimate rejection

ExplanationUltimate rejection is the most attenuation a filter provides to unwanted signals.

G7C14

The bandwidth of a band-pass filter is measured between what two frequencies?

Upper and lower half-power

ExplanationBandwidth is the range between the two points where power drops by half (3 dB).

G8A01

How is direct binary FSK modulation generated?

By changing an oscillator’s frequency directly with a digital control signal

ExplanationFSK (frequency-shift keying) shifts between two frequencies. Here the digital signal moves the oscillator itself.

G8A02

What is the name of the process that changes the phase angle of an RF signal to convey information?

Phase modulation

ExplanationPhase modulation encodes information by shifting the wave’s phase.

G8A03

What is the name of the process that changes the instantaneous frequency of an RF wave to convey information?

Frequency modulation

ExplanationFM varies the frequency of the carrier in step with the audio.

G8A04

What emission is produced by a reactance modulator connected to a transmitter RF amplifier stage?

Phase modulation

ExplanationA reactance modulator changes the circuit’s tuning, which shifts the phase.

G8A05

What type of modulation varies the instantaneous power level of the RF signal?

Amplitude modulation

ExplanationAM varies the strength of the carrier to carry information.

G8A06

Which of the following is characteristic of QPSK31?

All these choices are correct

ExplanationQPSK31 is sideband sensitive, has error correction, and uses about the same bandwidth as BPSK31.

G8A07

Which of the following phone emissions uses the narrowest bandwidth?

Single sideband

ExplanationSSB is the narrowest voice mode.

G8A08

Which of the following is an effect of overmodulation?

Excessive bandwidth

ExplanationToo much modulation spreads the signal across a wider part of the band and interferes with others.

G8A09

What type of modulation is used by FT8?

8-tone frequency shift keying

ExplanationFT8 sends data using eight different tones.

G8A10

What is meant by the term “flat-topping,” when referring to an amplitude-modulated phone signal?

Signal distortion caused by excessive drive or speech levels

ExplanationIf you overdrive the transmitter, the peaks get clipped flat, which distorts your voice.

G8A11

What is the modulation envelope of an AM signal?

The waveform created by connecting the peak values of the modulated signal

ExplanationThe envelope is the outline you get by tracing the peaks of the signal. It follows the audio.

G8A12

What is QPSK modulation?

Modulation in which digital data is transmitted using 0-, 90-, 180- and 270-degrees phase shift to represent pairs of bits

ExplanationQPSK uses four phase positions so each shift carries two bits.

G8A13

What is a link budget?

The sum of transmit power and antenna gains minus system losses as seen at the receiver

ExplanationA link budget adds up all the gains and subtracts all the losses between two stations to find the signal at the receiver.

G8A14

What is link margin?

The difference between received power level and minimum required signal level at the input to the receiver

ExplanationLink margin is the extra signal strength you have above the minimum needed to decode.

G8B01

Which mixer input is varied or tuned to convert signals of different frequencies to an intermediate frequency (IF)?

Local oscillator

ExplanationTuning the local oscillator makes a receiver select different frequencies.

G8B02

What is the term for interference from a signal at twice the IF frequency from the desired signal?

Image response

ExplanationAn image is an unwanted signal that mixes to the same IF as your wanted signal.

G8B03

What is another term for the mixing of two RF signals?

Heterodyning

ExplanationHeterodyning combines two signals to produce sum and difference frequencies.

G8B04

What is the stage in a VHF FM transmitter that generates a harmonic of a lower frequency signal to reach the desired operating frequency?

Multiplier

ExplanationA multiplier takes a lower frequency and creates a harmonic at a multiple of it.

G8B05

Which intermodulation products are closest to the original signal frequencies?

Odd-order

ExplanationOdd-order products land right next to the original signals, so they are the hardest to filter out.

G8B06

What is the total bandwidth of an FM phone transmission having 5 kHz deviation and 3 kHz modulating frequency?

16 kHz

ExplanationBandwidth = 2 × (deviation + modulating frequency) = 2 × (5 + 3) = 16 kHz.

G8B07

What is the frequency deviation for a 12.21 MHz reactance modulated oscillator in a 5 kHz deviation, 146.52 MHz FM phone transmitter?

416.7 Hz

ExplanationThe oscillator’s deviation is multiplied up to the final frequency. 5000 Hz × (12.21 ÷ 146.52) ≈ 416.7 Hz.

G8B08

Why is it important to know the duty cycle of the mode you are using when transmitting?

Some modes have high duty cycles that could exceed the transmitter’s average power rating

ExplanationDuty cycle is the fraction of time you transmit. Digital modes transmit constantly and can overheat a radio.

G8B09

Why is it good to match receiver bandwidth to the bandwidth of the operating mode?

It results in the best signal-to-noise ratio

ExplanationA filter that fits the signal passes the signal and blocks extra noise.

G8B10

What is the relationship between transmitted symbol rate and bandwidth?

Higher symbol rates require wider bandwidth

ExplanationSending data faster takes up more room on the band.

G8B11

What combination of a mixer’s Local Oscillator (LO) and RF input frequencies is found in the output?

The sum and difference

ExplanationA mixer produces the sum and the difference of its two input frequencies.

G8B12

What process combines two signals in a non-linear circuit to produce unwanted spurious outputs?

Intermodulation

ExplanationWhen strong signals mix in a non-linear circuit, they create new, unwanted signals.

G8B13

Which of the following is an odd-order intermodulation product of frequencies F1 and F2?

2F1-F2

ExplanationOdd-order products have coefficients that add up to an odd number. 2 + 1 = 3.

G8C02

Which digital mode is used as a low-power beacon for assessing HF propagation?

WSPR

ExplanationWSPR (“whisper”) sends tiny power beacons so you can see where they are heard.

G8C03

What part of a packet radio frame contains the routing and handling information?

Header

ExplanationThe header is at the front of a packet and says where it goes and how to handle it.

G8C04

Which of the following describes Baudot code?

A 5-bit code with additional start and stop bits

ExplanationBaudot is the classic teleprinter code used for RTTY. It uses five bits per character.

G8C05

In an ARQ mode, what is meant by a NAK response to a transmitted packet?

Request retransmission of the packet

ExplanationARQ means automatic repeat request. NAK says “not acknowledged, send it again.”

G8C06

What action results from a failure to exchange information due to excessive transmission attempts when using an ARQ mode?

The connection is dropped

ExplanationAfter too many failed retries, the link gives up and disconnects.

G8C07

Which of the following narrow-band digital modes can receive signals with very low signal-to-noise ratios?

FT8

ExplanationFT8 can be decoded even when signals are far below the noise.

G8C08

Which of the following statements is true about PSK31?

Upper case letters use longer Varicode bit sequences and thus slow down transmission

ExplanationIn PSK31, rarely used characters take longer codes, so capital letters make your typing slower.

G8C09

Which is true of mesh network microwave nodes?

If one node fails, a packet may still reach its target station via an alternate node

ExplanationIn a mesh network, data can take another route if one node goes down.

G8C10

How does forward error correction (FEC) allow the receiver to correct data errors?

By transmitting redundant information with the data

ExplanationFEC sends extra data so the receiver can fix errors without asking for a resend.

G8C11

How are the two separate frequencies of a Frequency Shift Keyed (FSK) signal identified?

Mark and space

ExplanationThe two tones in FSK are called mark and space.

G8C12

Which type of code is used for sending characters in a PSK31 signal?

Varicode

ExplanationVaricode gives common letters short codes and rare ones long codes.

G8C13

What is indicated on a waterfall display by one or more vertical lines on either side of a data mode or RTTY signal?

Overmodulation

ExplanationExtra lines beside a signal mean it is overdriven and spilling over.

G8C14

Which of the following describes a waterfall display?

Frequency is horizontal, signal strength is intensity, time is vertical

ExplanationA waterfall shows signals as bright traces. Frequency goes across and time scrolls downward.

G8C15

What does an FT8 signal report of +3 mean?

The signal-to-noise ratio is equivalent to +3dB in a 2.5 kHz bandwidth

ExplanationFT8 reports are in dB relative to noise in a 2.5 kHz bandwidth, not S units.

G8C16

Which of the following provide digital voice modes?

DMR, D-STAR, and SystemFusion

ExplanationThese three are digital voice systems. FT8 and Winlink send data, not voice.

G9A01

Which of the following factors determine the characteristic impedance of a parallel conductor feed line?

The distance between the centers of the conductors and the radius of the conductors

ExplanationImpedance depends on how far apart the wires are and how thick they are, not on length or frequency.

G9A02

What is the relationship between high standing wave ratio (SWR) and transmission line loss?

High SWR increases loss in a lossy transmission line

ExplanationReflected power travels back and forth through the cable, so more of it is lost as heat.

G9A03

What is the nominal characteristic impedance of “window line” transmission line?

450 ohms

ExplanationWindow line is a type of ladder line with openings in the insulation. It is about 450 ohms.

G9A04

What causes reflected power at an antenna’s feed point?

A difference between feed line impedance and antenna feed point impedance

ExplanationA mismatch between the cable and the antenna sends some power back toward the radio.

G9A05

How does the attenuation of coaxial cable change with increasing frequency?

Attenuation increases

ExplanationCoax loses more signal as the frequency goes up.

G9A06

In what units is RF feed line loss usually expressed?

Decibels per 100 feet

ExplanationCable loss is given in dB per 100 feet at a stated frequency.

G9A07

What must be done to prevent standing waves on a feed line connected to an antenna?

The antenna feed point impedance must be matched to the characteristic impedance of the feed line

ExplanationWhen the antenna matches the cable, no power reflects, so there are no standing waves.

G9A08

If the SWR on an antenna feed line is 5:1, and a matching network at the transmitter end of the feed line is adjusted to present a 1:1 SWR to the transmitter, what is the resulting SWR on the feed line?

5:1

ExplanationA tuner at the radio can’t fix the mismatch at the antenna. The cable still has a 5:1 SWR.

G9A09

What standing wave ratio results from connecting a 50-ohm feed line to a 200-ohm resistive load?

4:1

ExplanationSWR = 200 ÷ 50 = 4. Divide the larger impedance by the smaller one.

G9A10

What standing wave ratio results from connecting a 50-ohm feed line to a 10-ohm resistive load?

5:1

ExplanationSWR = 50 ÷ 10 = 5. Larger divided by smaller.

G9A11

What is the effect of transmission line loss on SWR measured at the input to the line?

Higher loss reduces SWR measured at the input to the line

ExplanationA lossy cable absorbs reflected power, so SWR at the radio looks better than at the antenna.

G9B01

What is a characteristic of a random-wire HF antenna connected directly to the transmitter?

Station equipment may carry significant RF current

ExplanationWith no proper ground or feed line, RF can end up on your radio and cables.

G9B02

Which of the following is a common way to adjust the feed point impedance of an elevated quarter-wave ground-plane vertical antenna to be approximately 50 ohms?

Slope the radials downward

ExplanationDrooping the radials raises the impedance from about 36 ohms to near 50 ohms.

G9B03

Which of the following best describes the radiation pattern of a quarter-wave ground-plane vertical antenna?

Omnidirectional in azimuth

ExplanationA vertical radiates equally in all compass directions.

G9B04

What is the radiation pattern of a dipole antenna in free space in a plane containing the conductor?

It is a figure-eight at right angles to the antenna

ExplanationA dipole is strongest broadside to the wire and weak off its ends.

G9B05

How does antenna height affect the azimuthal radiation pattern of a horizontal dipole HF antenna at elevation angles higher than about 45 degrees?

If the antenna is less than 1/2 wavelength high, the azimuthal pattern is almost omnidirectional

ExplanationA low dipole radiates nearly equally in every direction at high angles.

G9B06

Where should the radial wires of a ground-mounted vertical antenna system be placed?

On the surface or buried a few inches below the ground

ExplanationRadials spread out flat at ground level to complete the antenna.

G9B07

How does the feed point impedance of a horizontal 1/2 wave dipole antenna change as the antenna height is reduced to 1/10 wavelength above ground?

It steadily decreases

ExplanationLow antennas see a lower feed point impedance because of ground effects.

G9B08

How does the feed point impedance of a 1/2 wave dipole change as the feed point is moved from the center toward the ends?

It steadily increases

ExplanationImpedance is lowest at the center and highest at the ends.

G9B09

Which of the following is an advantage of using a horizontally polarized as compared to a vertically polarized HF antenna?

Lower ground losses

ExplanationHorizontal antennas lose less energy to the ground.

G9B10

What is the approximate length for a 1/2 wave dipole antenna cut for 14.250 MHz?

33 feet

ExplanationLength in feet ≈ 468 ÷ frequency in MHz. 468 ÷ 14.25 ≈ 33.

G9B11

What is the approximate length for a 1/2 wave dipole antenna cut for 3.550 MHz?

132 feet

Explanation468 ÷ 3.55 ≈ 132 feet.

G9B12

What is the approximate length for a 1/4 wave monopole antenna cut for 28.5 MHz?

8 feet

ExplanationA quarter-wave is 234 ÷ frequency in MHz. 234 ÷ 28.5 ≈ 8 feet.

G9C01

Which of the following would increase the bandwidth of a Yagi antenna?

Larger-diameter elements

ExplanationFatter elements let the antenna work over a wider range of frequencies.

G9C02

What is the approximate length of the driven element of a Yagi antenna?

1/2 wavelength

ExplanationThe driven element is the part connected to the feed line. It is about a half wave long.

G9C03

How do the lengths of a three-element Yagi reflector and director compare to that of the driven element?

The reflector is longer, and the director is shorter

ExplanationThe reflector is a bit longer than the driven element and the director a bit shorter.

G9C04

How does antenna gain in dBi compare to gain stated in dBd for the same antenna?

Gain in dBi is 2.15 dB higher

ExplanationdBi compares to an ideal point source and dBd to a dipole. A dipole itself has 2.15 dBi.

G9C05

What is the primary effect of increasing boom length and adding directors to a Yagi antenna?

Gain increases

ExplanationA longer Yagi with more directors focuses the signal more tightly.

G9C07

What does “front-to-back ratio” mean in reference to a Yagi antenna?

The power radiated in the major lobe compared to that in the opposite direction

ExplanationIt tells how much weaker the signal is behind the antenna than in front.

G9C08

What is meant by the “main lobe” of a directive antenna?

The direction of maximum radiated field strength from the antenna

ExplanationThe main lobe is where the antenna sends the strongest signal.

G9C09

In free space, how does the gain of two three-element, horizontally polarized Yagi antennas spaced vertically 1/2 wavelength apart typically compare to the gain of a single three-element Yagi?

Approximately 3 dB higher

ExplanationStacking two identical antennas doubles the power focused, about 3 dB.

G9C10

Which of the following can be adjusted to optimize forward gain, front-to-back ratio, or SWR bandwidth of a Yagi antenna?

All these choices are correct

ExplanationBoom length, the number of elements, and element spacing all affect Yagi performance.

G9C11

What is a beta or hairpin match?

A shorted transmission line stub placed at the feed point of a Yagi antenna to provide impedance matching

ExplanationA hairpin-shaped wire at the feed point matches the antenna to the feed line.

G9C12

Which of the following is a characteristic of using a gamma match with a Yagi antenna?

It does not require the driven element to be insulated from the boom

ExplanationA gamma match lets the driven element be bolted directly to the boom.

G9D01

Which of the following antenna types will be most effective as a near vertical incidence skywave (NVIS) antenna for short-skip communications on 40 meters during the day?

A horizontal dipole placed between 1/10 and 1/4 wavelength above the ground

ExplanationA low horizontal dipole sends most of its signal straight up, which is what NVIS needs.

G9D02

What is the feed point impedance of an end-fed half-wave antenna?

Very high

ExplanationThe end of a half-wave wire has high voltage and low current, which means very high impedance.

G9D03

In which direction is the maximum radiation from a VHF/UHF “halo” antenna?

Omnidirectional in the plane of the halo

ExplanationA halo is a loop antenna that sends horizontally polarized signals equally in all horizontal directions.

G9D04

What is the primary function of antenna traps?

To enable multiband operation

ExplanationA trap is a tuned circuit that makes one wire work as an antenna on several bands.

G9D05

What is an advantage of vertically stacking horizontally polarized Yagi antennas?

It narrows the main lobe in elevation

ExplanationStacking squeezes the beam up and down, which concentrates more signal toward the horizon.

G9D06

Which of the following is an advantage of a log-periodic antenna?

Wide bandwidth

ExplanationA log-periodic works over a wide range of frequencies without retuning.

G9D07

Which of the following describes a log-periodic antenna?

Element length and spacing vary logarithmically along the boom

ExplanationIts elements get progressively longer or shorter along the boom in a set pattern.

G9D08

How does a “screwdriver” mobile antenna adjust its feed point impedance?

By varying the base loading inductance

ExplanationA motor changes the coil at the base so the antenna matches on different frequencies.

G9D09

What is the primary use of a Beverage antenna?

Directional receiving for MF and low HF bands

ExplanationA Beverage is a very long wire used only for receiving, to hear weak signals on low bands.

G9D10

In which direction or directions does an electrically small loop (less than 1/10 wavelength in circumference) have nulls in its radiation pattern?

Broadside to the loop

ExplanationSmall loops have deep nulls straight out from their face, useful for cutting out noise.

G9D11

Which of the following is a disadvantage of multiband antennas?

They have poor harmonic rejection

ExplanationAntennas that work on many bands can also radiate unwanted harmonics.

G9D12

What is the common name of a dipole with a single central support?

Inverted V

ExplanationA dipole hung from a single support in the center, with the ends sloping down, is an inverted V.

G0A01

What is one way that RF energy can affect human body tissue?

It heats body tissue

ExplanationRF energy is non-ionizing, but at high power it can warm tissue. That is the main concern.

G0A02

Which of the following is used to determine RF exposure from a transmitted signal?

All these choices are correct

ExplanationFrequency, power density, and duty cycle all affect how much RF a person absorbs.

G0A03

How can you determine that your station complies with FCC RF exposure regulations?

All these choices are correct

ExplanationYou can calculate using OET Bulletin 65, use computer modeling, or measure field strength with calibrated equipment.

G0A04

What does “time averaging” mean when evaluating RF radiation exposure?

The total RF exposure averaged over a certain period

ExplanationExposure limits are based on the average over time, not on each short burst.

G0A05

What must you do if an evaluation of your station shows that the RF energy radiated by your station exceeds permissible limits for possible human absorption?

Take action to prevent human exposure to the excessive RF fields

ExplanationIf your station is over the limit, you must keep people out of the area, such as by moving the antenna or reducing power.

G0A06

What must you do if your station fails to meet the FCC RF exposure exemption criteria?

Perform an RF Exposure Evaluation in accordance with FCC OET Bulletin 65

ExplanationLow-power stations are exempt. If you aren’t, you must evaluate your exposure.

G0A07

What is the effect of modulation duty cycle on RF exposure?

A lower duty cycle permits greater power levels to be transmitted

ExplanationLower duty cycle means you transmit less of the time, so average exposure is lower.

G0A08

Which of the following steps must an amateur operator take to ensure compliance with RF safety regulations?

Perform a routine RF exposure evaluation and prevent access to any identified high exposure areas

ExplanationEvaluate your station and keep people out of any areas where exposure is too high.

G0A09

What type of instrument can be used to accurately measure an RF field strength?

A calibrated field strength meter with a calibrated antenna

ExplanationAccurate RF measurements need a meter and antenna that have been calibrated.

G0A10

What should be done if evaluation shows that a neighbor might experience more than the allowable limit of RF exposure from the main lobe of a directional antenna?

Take precautions to ensure that the antenna cannot be pointed in their direction when they are present

ExplanationBlock the antenna’s direction while they are there. For example, you could set a limit on its rotation.

G0A11

What precaution should be taken if you install an indoor transmitting antenna?

Make sure that MPE limits are not exceeded in occupied areas

ExplanationAn indoor antenna is close to people. MPE (maximum permissible exposure) limits must still be met.

G0A12

What stations are subject to the FCC rules on RF exposure?

All stations with a time-averaged transmission of more than one milliwatt

ExplanationNearly all stations must follow the RF exposure rules, since the cutoff is only one milliwatt.

G0B01

Which wire or wires in a four-conductor 240 VAC circuit should be attached to fuses or circuit breakers?

Only the hot wires

ExplanationFuses and breakers protect the live (hot) wires. Neutral and ground are not fused.

G0B02

According to the National Electrical Code, what is the minimum wire size that may be used safely for wiring with a 20-ampere circuit breaker?

AWG number 12

Explanation12-gauge wire is the minimum for a 20-amp circuit. Thinner wire could overheat.

G0B03

Which size of fuse or circuit breaker would be appropriate to use with a circuit that uses AWG number 14 wiring?

15 amperes

Explanation14-gauge wire is safe up to 15 amps. A bigger breaker wouldn’t trip before the wire got hot.

G0B04

Where should the station’s lightning protection ground system be located?

Outside the building

ExplanationLightning energy should be diverted to ground before it enters your home.

G0B05

Which of the following conditions will cause a ground fault circuit interrupter (GFCI) to disconnect AC power?

Current flowing from one or more of the hot wires directly to ground

ExplanationA GFCI cuts power in a fraction of a second if current leaks to ground, such as through a person.

G0B06

Which of the following is covered by the National Electrical Code?

Electrical safety of the station

ExplanationThe NEC sets standards for safe electrical wiring, including in your ham shack.

G0B07

Which of these choices should be observed when climbing a tower using a safety harness?

Confirm that the harness is rated for the weight of the climber and that it is within its allowable service life

ExplanationHarnesses have weight ratings and expire. Check both before climbing.

G0B08

What should be done before climbing a tower that supports electrically powered devices?

Make sure all circuits that supply power to the tower are locked out and tagged

ExplanationLockout/tagout makes sure no one switches power on while you are up there.

G0B09

Which of the following is true of an emergency generator installation?

The generator should be operated in a well-ventilated area

ExplanationGenerators produce deadly carbon monoxide, so run them outdoors or where air flows freely.

G0B10

Which of the following is a danger from lead-tin solder?

Lead can contaminate food if hands are not washed carefully after handling the solder

ExplanationWash your hands after soldering so no lead reaches your food or mouth.

G0B11

Which of the following is required for lightning protection ground rods?

They must be bonded together with all other grounds

ExplanationAll grounds must be connected to prevent dangerous voltage differences.

G0B12

What is the purpose of a power supply interlock?

To ensure that dangerous voltages are removed if the cabinet is opened

ExplanationAn interlock is a safety switch that shuts off power when you open the case.

G0B13

Where should lightning arrestors be located?

Where the feed lines enter the building

ExplanationThe arrestor diverts a surge to ground before it enters the house.